Electrochemo-magneto abrasive flow machine setup fabrication and experimental investigation of the process alongwith mathematical modeling and optimization
Main Article Content
Abstract
Downloads
Article Details
1. Proposal of Policy for Free Access Periodics
Authors whom publish in this magazine should agree to the following terms:
a. Authors should keep the copyrights and grant to the magazine the right of the first publication, with the work simultaneously permitted under the Creative Commons Attribution-NonCommercial-ShareAlike 4.0 that allows the sharing of the work with recognition of the authorship of the work and initial publication in this magazine.
b. Authors should have authorization for assuming additional contracts separately, for non-exclusive distribution of the version of the work published in this magazine (e.g.: to publish in an institutional repository or as book chapter), with recognition of authorship and initial publication in this magazine.
c. Authors should have permission and should be stimulated to publish and to distribute its work online (e.g.: in institutional repositories or its personal page) to any point before or during the publishing process, since this can generate productive alterations, as well as increasing the impact and the citation of the published work (See The Effect of Free Access).
Proposal of Policy for Periodic that offer Postponed Free Access
Authors whom publish in this magazine should agree to the following terms:
a. Authors should keep the copyrights and grant to the magazine the right of the first publication, with the work simultaneously permitted under the Creative Commons Attribution-NonCommercial-ShareAlike 4.0 [SPECIFY TIME HERE] after the publication, allowing the sharing of the work with recognition of the authorship of the work and initial publication in this magazine.
b. Authors should have authorization for assuming additional contracts separately, for non-exclusive distribution of the version of the work published in this magazine (e.g.: to publish in institutional repository or as book chapter), with recognition of authorship and initial publication in this magazine.
c. Authors should have permission and should be stimulated to publish and to distribute its work online (e.g.: in institutional repositories or its personal page) to any point before or during the publishing process, since this can generate productive alterations, as well as increasing the impact and the citation of the published work (See The Effect of Free Access).
d. They allow some kind of open dissemination. Authors can disseminate their articles in open access, but with specific conditions imposed by the editor that are related to:
Version of the article that can be deposited in the repository:
Pre-print: before being reviewed by pairs.
Post-print: once reviewed by pairs, which can be:
The version of the author that has been accepted for publication.
The editor's version, that is, the article published in the magazine.
At which point the article can be made accessible in an open manner: before it is published in the magazine, immediately afterwards or if a period of seizure is required, which can range from six months to several years.
Where to leave open: on the author's personal web page, only departmental websites, the repository of the institution, the file of the research funding agency, among others.
References
JAIN. V. K. (2008) Abrasive-based nano-finishing techniques: an overview. Machining Science and Technology, An International Journal, v. 12, n. 3, p. 257-294.
KENDA, J.;PUSAVEC, F.; KOPAC. J. (2014) Modeling and Energy Efficiency of Abrasive Flow Machining on Tooling Industry Case Study. In: Proc. 2nd CIRP Conference on Surface Integrity, Procedia, p. 13-18.
KURITA, T.; HATTORI, M. (2006) A study of EDM and ECM/ECM-lapping complex machining technology. International Journal of Machine Tools & Manufacture, n. 46, p.1804-1810.
SINGH, A. K.; JHA, S.; PANDEY, P. M. (2012) Nanofinishing of a typical 3D ferromagnetic workpiece using ball end magnetorheological finishing process. In Proc. International Journal of Machine Tools & Manufacture, n. 63, p. 21-31.
TANG, B.; JI, S.; TAN, D. (2010) Structural Surface of Mould Softness Abrasive Flow Precision Polishing Machining Method Based On VOF. International Conference on Electrical and Control Engineering, Procedia.
UHLMANN, E.; MIHOTOVIC, V.; COENEN, A. (2009) Modelling the abrasive flow machining process on advanced ceramic materials. Journal of Materials Processing Technology, n. 209, p. 6062-6066.
VENKATESH, G.; SHARMA, A. K.; SINGH, N.; KUMAR, P. (2014) Finishing of Bevel Gears using Abrasive Flow Machining. In: Proc. 12th Global Congress on Manufacturing and Management - GCMM, Procedia, p. 320-328.
VENKATESH, G.; SHARMA, A. K.; SINGH, N. (2015) Simulation of media behaviour in vibration assisted abrasive flow machining. Simulation Modelling Practice and Theory, n. 51, p. 1-13.
WILLIAMS, R. R.; MELTON, V. L. (1998) Abrasive flow finishing of stereolithographic prototypes. Rapid Prototyping Journal, v. 4, n. 2, p. 56-67.
WILLIAMS, R. R.; WALCZYK, D. F.; DANG, H. T. (2007) Using abrasive flow machining to seal and finish conformal channels in laminated tooling. Rapid Prototyping Journal, n. 13, p. 64-75.
YAN, B. H.; WANG, C. C.; LIN, Y. C. (2000) Feasibility study of rotary electrical discharge machining with ball burnishing for Al2O3/6061Al composite. International Journal of Machine Tools & Manufacture, n. 40, p. 1403-1421.
YAN, B. H.; CHANG, G. W.; CHENG, T. J.; HSU, R. T. (2003) Electrolytic magnetic abrasive finishing, International Journal of Machine Tools & Manufacture, n. 43, p. 1355-1366.
YANG, C. T.; SONG, S. L.; YAN, B. H.; HUANG, F. Y. (2006) Improving machining performance of wire electrochemical discharge machining by adding SiC abrasive to electrolyte, International Journal of Machine Tools & Manufacture, n. 46, p. 2044-2050.
ZABORSKI, S.; ŁUPAK, M.; PORO, D. (2004) Wear of cathode in abrasive electrochemical grinding of hardly machined materials, Journal of Materials Processing Technology, n. 149, p. 414-418.
ZHANG, S.; LIU, W.; YANG, L.; ZHU, L-C.; LI, C.; XIN. J. (2009) Study On Abrasive Flow Ultra-Precision Polishing Technology of Small Hole. Proceedings of the IEEE. International Conference on Mechatronics and Automation, Changchun, China, Procedia, August 9-12.