About the internal combustion engines forces
Article Sidebar
Main Article Content
صندلی اداریAbstract
The paper presents an algorithm to set the parameters of the dynamics of the classic mechanism the main of internal combustion. It shows the distribution of the forces (on the main mechanism of the engine) on engines with internal combustion. Dynamic, the gears can be distributed in the same way as forces. Practically, in the dynamic regimes, the velocities have the same synchronization as forces. The method shall be applied separately for two distinct situations: when the engine is working on a compressor and in the system of the motor. For the two individual cases, two independent formulae are obtained for the dynamic cinematic forces (gearbox). The calculations shall be made for an engine with a single cylinder. The change of speed in the dynamics feels like a variation of the angular speed of the engine. It is more difficult to be taken into account (theoretically) effect on an engine with several cylinders.
Downloads
Article Details
1. Proposal of Policy for Free Access Periodics
Authors whom publish in this magazine should agree to the following terms:
a. Authors should keep the copyrights and grant to the magazine the right of the first publication, with the work simultaneously permitted under the Creative Commons Attribution-NonCommercial-ShareAlike 4.0 that allows the sharing of the work with recognition of the authorship of the work and initial publication in this magazine.
b. Authors should have authorization for assuming additional contracts separately, for non-exclusive distribution of the version of the work published in this magazine (e.g.: to publish in an institutional repository or as book chapter), with recognition of authorship and initial publication in this magazine.
c. Authors should have permission and should be stimulated to publish and to distribute its work online (e.g.: in institutional repositories or its personal page) to any point before or during the publishing process, since this can generate productive alterations, as well as increasing the impact and the citation of the published work (See The Effect of Free Access).
Proposal of Policy for Periodic that offer Postponed Free Access
Authors whom publish in this magazine should agree to the following terms:
a. Authors should keep the copyrights and grant to the magazine the right of the first publication, with the work simultaneously permitted under the Creative Commons Attribution-NonCommercial-ShareAlike 4.0 [SPECIFY TIME HERE] after the publication, allowing the sharing of the work with recognition of the authorship of the work and initial publication in this magazine.
b. Authors should have authorization for assuming additional contracts separately, for non-exclusive distribution of the version of the work published in this magazine (e.g.: to publish in institutional repository or as book chapter), with recognition of authorship and initial publication in this magazine.
c. Authors should have permission and should be stimulated to publish and to distribute its work online (e.g.: in institutional repositories or its personal page) to any point before or during the publishing process, since this can generate productive alterations, as well as increasing the impact and the citation of the published work (See The Effect of Free Access).
d. They allow some kind of open dissemination. Authors can disseminate their articles in open access, but with specific conditions imposed by the editor that are related to:
Version of the article that can be deposited in the repository:
Pre-print: before being reviewed by pairs.
Post-print: once reviewed by pairs, which can be:
The version of the author that has been accepted for publication.
The editor's version, that is, the article published in the magazine.
At which point the article can be made accessible in an open manner: before it is published in the magazine, immediately afterwards or if a period of seizure is required, which can range from six months to several years.
Where to leave open: on the author's personal web page, only departmental websites, the repository of the institution, the file of the research funding agency, among others.
References
AMORESANO, A.; AVAGLIANO, V.; NIOLA, V.; QUAREMBA, G. (2013) The Assessment of the in-Cylinder Pressure by Means of the Morpho-Dynamical Vibration Analysis – Methodology and Application, in IREME Journal, v. 7, n. 6, p. 999-1006.
ANDERSON, R. B. (1984) The Fischer-Tropsch Synthesis, Academic Press.
ANTONESCU, P.; PETRESCU, F. I. T. (1985) An analytical method of synthesis of cam mechanism and flat stick. Proceedings of the 4th International Symposium on Theory and Practice of Mechanisms, (TPM’ 89), Bucharest.
ANTONESCU, P.; PETRESCU, F. I. T. (1989) Contributions to kinetoplast dynamic analysis of distribution mechanisms. SYROM’89, Bucharest.
ANTONESCU, P.; OPREAN, M.; PETRESCU, F. I. T. (1985a) Contributions to the synthesis of oscillating cam mechanism and oscillating flat stick. Proceedings of the 4th International Symposium on Theory and Practice of Mechanisms, (TPM’ 85), Bucharest.
ANTONESCU, P.; OPREAN, M.; PETRESCU, F. I. T. (1985b) At the projection of the oscillate cams, there are mechanisms and distribution variables. Proceedings of the 5th Conference of Engines, Automobiles, Tractors and Agricultural Machines, (TAM’ 58), I-Motors and Cars, Brasov.
ANTONESCU, P.; OPREAN, M.; PETRESCU, F. I. T. (1986) Projection of the profile of the rotating camshaft acting on the oscillating plate with disengagement. Proceedings of the 3rd National Computer-aided Design Symposium in the field of Mechanisms and Machine Parts, (MMP’ 86), Brasov.
ANTONESCU, P.; OPREAN, M.; PETRESCU, F. I. T. (1987) Dynamic analysis of the cam distribution mechanisms. Proceedings of the 7th National Symposium on Industrial Robots and Space Mechanisms, (RSM’ 87), Bucharest.
ANTONESCU, P.; OPREAN, M.; PETRESCU, F. (1988) Analytical synthesis of Kurz profile, rotating the flat cam. Mach, Build. Rev.
ANTONESCU, P.; PETRESCU, F. I. T.; ANTONESCU, O. (1994) Contributions to the synthesis of the rotating cam mechanism and the tip of the balancing tip. Brasov.
ANTONESCU, P.; PETRESCU, F. I. T.; ANTONESCU, O. (1997) Geometrical synthesis of the rotary cam and balance tappet mechanism. Bucharest, n. 3, p. 23-23.
ANTONESCU, P.; PETRESCU, F. I. T.; ANTONESCU, O. (2000a) Contributions to the synthesis of the rotary disc-cam profile. Proceedings of the 8th International Conference on the Theory of Machines and Mechanisms, (TMM’ 00), Liberec, Czech Republic, p. 51-56.
ANTONESCU, P.; PETRESCU, F. I. T.; ANTONESCU, O. (2000b) Synthesis of the rotary cam profile with balance follower. Proceedings of the 8th Symposium on Mechanisms and Mechanical Transmissions, (MMT’ 00), Timişoara, p. 39-44.
ANTONESCU, P.; PETRESCU, F. I. T.; ANTONESCU, O. (2001) Contributions to the synthesis of mechanisms with rotary disc-cam. Proceedings of the 8th IFToMM International Symposium on Theory of Machines and Mechanisms, (TMM’ 01), Bucharest, ROMANIA, p. 31-36.
ATEFI, G.;ABDOUS , M. A.; GANJEHKAVIRI, A. (2008) Analytical Solution of Temperature Field in Hollow Cylinder under Time Dependent Boundary Condition Using Fourier series, Am. J. Eng. Applied Sci., v. 1, n. 2, p. 141-148. DOI: 10.3844/ajeassp.2008.141.148
AVAEI, A.; GHOTBI, A. R.; ARYAFAR, M. (2008) Investigation of Pile-Soil Interaction Subjected to Lateral Loads in Layered Soils, Am. J. Eng. Applied Sci., v. 1, n. 1, p. 76-81. DOI: 10.3844/ajeassp.2008.76.81
AVERSA, R.; PETRESCU, R. V. V.; APICELLA, A.; PETRESCU, F. I. T. (2017a) Nano-diamond hybrid materials for structural biomedical application. Am. J. Biochem. Biotechnol., n. 13, p. 34-41. DOI: 10.3844/ajbbsp.2017.34.41
AVERSA, R.; PETRESCU, R. V. V.; AKASH, B.; BUCINELL, R. B.; CORCHADO, J. M.; (2017b) Kinematics and forces to a new model forging manipulator. Am. J. Applied Sci., n. 14, p. 60-80. DOI: 10.3844/ajassp.2017.60.80
AVERSA, R.; PETRESCU, R. V. V.; APICELLA, A.; PETRESCU, F. I. T.; CALAUTIT, J. K. (2017c) Something about the V engines design. Am. J. Applied Sci., n. 14, p. 34-52. DOI: 10.3844/ajassp.2017.34.52
AVERSA, R.; PARCESEPE, D.; PETRESCU, R. V. V.; BERTO, F.; CHEN, G. (2017d) Process ability of bulk metallic glasses. Am. J. Applied Sci., n. 14, p. 294-301. DOI: 10.3844/ajassp.2017.294.301
AVERSA, R.; PETRESCU, R. V. V.; AKASH, B.; BUCINELL, R. B.; CORCHADO, J. M. (2017e) Something about the balancing of thermal motors. Am. J. Eng. Applied Sci., n. 10, p. 200.217. DOI: 10.3844/ajeassp.2017.200.217
AVERSA, R.; PETRESCU, F. I. T.; PETRESCU, R. V. V.; APICELLA, A. (2016a) Biomimetic FEA bone modeling for customized hybrid biological prostheses development. Am. J. Applied Sci., n. 13, p. 1060-1067. DOI: 10.3844/ajassp.2016.1060.1067
AVERSA, R.; PARCESEPE, D.; PETRESCU, R. V. V.; CHEN, G.; PETRESCU, F. I. T. (2016b) Glassy amorphous metal injection molded induced morphological defects. Am. J. Applied Sci., n. 13, p. 1476-1482. DOI: 10.3844/ajassp.2016.1476.1482
AVERSA, R.; PETRESCU, R. V. V.; PETRESCU, F. I. T.; APICELLA, A. (2016c) Smart-factory: Optimization and process control of composite centrifuged pipes. Am. J. Applied Sci., n. 13, p. 1330-1341. DOI: 10.3844/ajassp.2016.1330.1341
AVERSA, R.; TAMBURRINO, F.; PETRESCU, R. V. V.; PETRESCU, F. I. T.; ARTUR, M. (2016d) Biomechanically inspired shape memory effect machines driven by muscle like acting NiTi alloys. Am. J. Applied Sci., n. 13, p. 1264-1271. DOI: 10.3844/ajassp.2016.1264.1271
AVERSA, R.; BUZEA, E. M.; PETRESCU, R. V. V.; APICELLA, A.; NEACSA, M. (2016e) Present a mechatronic system having able to determine the concentration of carotenoids. Am. J. Eng. Applied Sci., n. 9, p. 1106-1111. DOI: 10.3844/ajeassp.2016.1106.1111
AVERSA, R.; PETRESCU, R. V. V.; R. SORRENTINO, PETRESCU, F. I. T.; APICELLA, A. (2016f) Hybrid ceramo-polymeric nanocomposite for biomimetic scaffolds design and preparation. Am. J. Eng. Applied Sci., n. 9, p. 1096-1105. DOI: 10.3844/ajeassp.2016.1096.1105
AVERSA, R.; PERROTTA, V.; PETRESCU, R. V. V.; MISIANO, C.; PETRESCU, F. I. T. (2016g) From structural colors to super-hydrophobicity and achromatic transparent protective coatings: Ion plating plasma assisted TiO2 and SiO2 nano-film deposition. Am. J. Eng. Applied Sci., n. 9, p. 1037-1045. DOI: 10.3844/ajeassp.2016.1037.1045
AVERSA, R.; PETRESCU, R. V. V.; PETRESCU, F. I. T.; APICELLA, A. (2016h) Biomimetic and evolutionary design driven innovation in sustainable products development. Am. J. Eng. Applied Sci., n. 9, p. 1027-1036. DOI: 10.3844/ajeassp.2016.1027.1036
AVERSA, R.; PETRESCU, R. V. V.; APICELLA, A.; PETRESCU, F. I. T. (2016i) Mitochondria are naturally micro robots - a review. Am. J. Eng. Applied Sci., n. 9, p. 991-1002. DOI: 10.3844/ajeassp.2016.991.1002
AVERSA, R.; PETRESCU, R. V. V.; APICELLA, A.; PETRESCU, F. I. T. (2016j) We are addicted to vitamins C and E-A review. Am. J. Eng. Applied Sci., n. 9, p. 1003-1018. DOI: 10.3844/ajeassp.2016.1003.1018
AVERSA, R.; PETRESCU, R. V. V.; APICELLA, A.; PETRESCU, F. I. T. (2016k) Physiologic human fluids and swelling behavior of hydrophilic biocompatible hybrid ceramo-polymeric materials. Am. J. Eng. Applied Sci., n. 9, p. 962-972. DOI: 10.3844/ajeassp.2016.962.972
AVERSA, R.; PETRESCU, R. V. V.; APICELLA, A.; PETRESCU, F. I. T. (2016l) One can slow down the aging through antioxidants. Am. J. Eng. Applied Sci., n. 9, p. 1112-1126. DOI: 10.3844/ajeassp.2016.1112.1126
AVERSA, R.; PETRESCU, R. V. V.; APICELLA, A.; PETRESCU, F. I. T. (2016m) About homeopathy or ≪Similia Similibus Curentur≫. Am. J. Eng. Applied Sci., n. 9, p. 1164-1172. DOI: 10.3844/ajeassp.2016.1164.1172
AVERSA, R.; PETRESCU, R. V. V.; APICELLA, A.; PETRESCU, F. I. T. (2016n) The basic elements of life's. Am. J. Eng. Applied Sci., n. 9, p. 1189-1197. DOI: 10.3844/ajeassp.2016.1189.1197
AVERSA, R.; PETRESCU, F. I. T.; PETRESCU, R. V. V.; APICELLA, A. (2016o) Flexible stem trabecular prostheses. Am. J. Eng. Applied Sci., n. 9, p. 1213-1221. DOI: 10.3844/ajeassp.2016.1213.122
AZAGA, M.; OTHMAN, M. (2008) Source Couple Logic (SCL, p. Theory and Physical Design, Am. J. Eng. Applied Sci., v. 1, n. 1, p. 24-32. DOI: 10.3844/ajeassp.2008.24.32
BISHOP J. L. H. (1950-51) An analytical approach to automobile valve gear design. Inst. of Mech. Engrs. Auto-Division Proc. 4, p. 150-160.
CAO, W.; DING, H.; BIN, Z.; ZIMING, C. (2013) New structural representation and digital-analysis platform for symmetrical parallel mechanisms. Int. J. Adv. Robotic Sys. DOI: 10.5772/56380
CHOI J. K.; KIM S. C. (1994) Hyundai Motor Co. Korea, An Experimental Study on the Frictional Characteristics in the Valve Train System. (945046), In FISITA CONGRESS, p. 17-21, Beijing, p. 374-380.
COMANESCU, A. (2010) Bazele Modelarii Mecanismelor. 1st Edn.; E. Politeh, Press, Bucureşti, p. 274.
DE FALCO, D.; DI MASSA, G.; PAGANO, S.; STRANO, S. (2013a) Motorcycle Handlebar Dynamic Response: Theoretical and Experimental Investigation, in IREME Journal, v. 7, n. 5, p. 795-801.
DE FALCO, D.; DI MASSA, G.; PAGANO, S. (2013b) A Full Scale Motorcycle Dynamic Rig, in IREME Journal, v. 7, n. 3, p. 519-526.
DONG, H.; GIAKOUMIDIS, N.; FIGUEROA, N.; MAVRIDIS, N. (2013) Approaching behaviour monitor and vibration indication in developing a General Moving Object Alarm System (GMOAS). Int. J. Adv. Robotic Sys. DOI: 10.5772/56586
YOUSIF EL-TOUS, (2008) Pitch Angle Control of Variable Speed Wind Turbine, Am. J. Eng. Applied Sci., v. 1, n. 2, p. 118-120. DOI: 10.3844/ajeassp.2008.118.120
FRANKLIN, D. J. (1930) Ingenious Mechanisms for Designers and Inventors. 1st Edn.; Industrial Press Publisher.
GANAPATHI, P.; ROBINSON, Y. (2013) Experimental Investigation on the Performance, Emission and Combustion Characteristics of a Diesel Engine Fuelled with Polymer Oil – Ethanol Blends, in IREME Journal, v. 7, n. 5, July 2013, p. 919-924.
HE, B.; WANG, Z.; LI, Q.; XIE, H.; SHEN, R. (2013) An analytic method for the kinematics and dynamics of a multiple-backbone continuum robot. IJARS. DOI: 10.5772/54051
HEYWOOD, J. B. (1988) Internal Combustion Engine Fundamentals, McGraw-Hill.
HRONES J. A. (1948) An analysis of Dynamic Forces in a Cam-Driver System, Trans. ASME, v. 70, p. 473-482.
JOLGAF, M.; SULAIMAN, S. B.; ARIFFIN, M. K. A.; FAIEZA, A. A. (2008) Closed Die Forging Geometrical Parameters Optimization for Al-MMC, Am. J. Eng. Applied Sci., v. 1, n. 1, p. 1-6. DOI : 10.3844/ajeassp.2008.1.6
KANNAPPAN, A. N.; KESAVASAMY, R.; PONNUSWAMY, V. (2008) Molecular Interaction Studies of H-Bonded Complexes of Benzamide in 1,4-Dioxan with Alcohols From Acoustic and Thermodynamic Parameters, Am. J. Eng. Applied Sci., v. 1, n. 2, p. 95-99. DOI: 10.3844/ajeassp.2008.95.99
KARIKALAN, L.; CHANDRASEKARAN, M.; SUDHAGAR, K. (2013) Comparative Studies on Vegetable Oil Usage in CI Engines as an Alternative to Diesel Fuel, in IREME Journal, V. 7, N. 4, May 2013, p. 705-715.
LEE, B. J. (2013) Geometrical derivation of differential kinematics to calibrate model parameters of flexible manipulator. Int. J. Adv. Robotic Sys. DOI: 10.5772/55592
LEIDEL, J. A. (1997) An Optimized Low Heat Rejection Engine for Automotive Use, SAE paper No. 970068, 1997.
LIN, W.; LI, B.; YANG, X.; ZHANG, D. (2013) Modelling and control of inverse dynamics for a 5-DOF parallel kinematic polishing machine. Int. J. Adv. Robotic Sys. DOI: 10.5772/54966
LIU, H.; ZHOU, W.; LAI, X.; ZHU, S. (2013) An efficient inverse kinematic algorithm for a PUMA560-structured robot manipulator. IJARS. DOI: 10.5772/56403
MAHALINGAM, S.; RAMESH BAPU, B. R. (2013) Experimental and Emission Analysis of Rubber Seed Oil and Jatropha Oil Blends with Diesel in Compression Ignition Engine, in IREME Journal, v. 7, n. 5, p. 955-959.
MEENA, P.; RITTIDECH, S. (2008) Comparisons of Heat Transfer Performance of a Closed-looped Oscillating Heat Pipe and Closed-looped Oscillating Heat Pipe with Check Valves Heat Exchangers, Am. J. Eng. Applied Sci., v. 1, n. 1, p. 7-11. DOI: 10.3844/ajeassp.2008.7.11
MEENA, P.; RITTIDECH, S.; TAMMASAENG, P. (2008) Effect of Inner Diameter and Inclination Angles on Operation Limit of Closed-Loop Oscillating Heat-Pipes with Check Valves, Am. J. Eng. Applied Sci., v. 1, n. 2, p. 100-103. DOI: 10.3844/ajeassp.2008.100.103
MIRSAYAR, M.M.; JONEIDI, V. A.; PETRESCU, R. V. V.; PETRESCU, F. I. T.; BERTO, F. (2017) Extended MTSN criterion for fracture analysis of soda lime glass. Eng. Fracture Mechan., n. 178, p. 50-59. DOI: 10.1016/j.engfracmech.2017.04.018
NAIMA, K.; LIAZID, A. (2013) Numerical Investigation on Combustion Behaviors of Direct-Injection Spark Ignition Engine Fueled with CNG-Hydrogen Blends, in IREME Journal, v. 7, n. 4, p. 652-663.
NARASIMAN, V.; JEYAKUMAR, S.; MANI, M. (2013) Optimizing the Compression Ratio of C.I. Engine Fuelled in Sardine Oil Ethyl Ester, in IREME Journal, v. 7, n. 3, p. 463-467.
NG, K. C.; YUSOFF, M. Z.; MUNISAMY, K.; HASINI, H.; SHUAIB, N. H. (2008) Time-Marching Method for Computations of High-Speed Compressible Flow on Structured and Unstructured Grid, Am. J. Eng. Applied Sci., v. 1, n. 2, p. 89-94. DOI: 10.3844/ajeassp.2008.89.94
PADULA, F.; PERDEREAU, V. (2013) An on-line path planner for industrial manipulators. Int. J. Adv. Robotic Sys. DOI: 10.5772/55063
PANNIRSELVAM, N.; RAGHUNATH, P. N.; SUGUNA, K. (2008) Neural Network for Performance of Glass Fibre Reinforced Polymer Plated RC Beams, Am. J. Eng. Applied Sci., v. 1, n. 1, p. 82-88. DOI: 10.3844/ajeassp.2008.82.88
PERUMAAL, S.; JAWAHAR, N. (2013) Automated trajectory planner of industrial robot for pick-and-place task. IJARS. DOI: 10.5772/53940
PETRESCU, F. I. T.; PETRESCU, R. (1995a) Contributions to optimization of the polynomial motion laws of the stick from the internal combustion engine distribution mechanism. Bucharest, n. 1, p. 249-256.
PETRESCU, F. I. T.; PETRESCU, R. (1995b) Contributions to the synthesis of internal combustion engine distribution mechanisms. Bucharest, n. 1, p. 257-264.
PETRESCU, F. I. T.; PETRESCU, R. (1997a) Dynamics of cam mechanisms (exemplified on the classic distribution mechanism). Bucharest, n. 3, p. 353-358.
PETRESCU, F. I. T.; PETRESCU, R. (1997b) Contributions to the synthesis of the distribution mechanisms of internal combustion engines with a Cartesian coordinate method. Bucharest, n. 3, p. 359-364.
PETRESCU, F. I. T.; PETRESCU, R. (1997c) Contributions to maximizing polynomial laws for the active stroke of the distribution mechanism from internal combustion engines. Bucharest, n. 3, p. 365-370.
PETRESCU, F. I. T.; PETRESCU, R. (2000a) Synthesis of distribution mechanisms by the rectangular (Cartesian) coordinate method. Proceedings of the 8th National Conference on International Participation, (CIP' 00), Craiova, Romania, p. 297-302.
PETRESCU, F. I. T.; PETRESCU, R. (2000b). The design (synthesis) of cams using the polar coordinate method (triangle method). Proceedings of the 8th National Conference on International Participation, (CIP' 00), Craiova, Romania, p. 291-296.
PETRESCU, F. I. T.; PETRESCU, R. (2002a) Motion laws for cams. Proceedings of the International Computer Assisted Design, National Symposium Participation, (SNP' 02), Braşov, p. 321-326.
PETRESCU, F. I. T.; PETRESCU, R. (2002b) Camshaft dynamics elements. Proceedings of the International Computer Assisted Design, National Participation Symposium, (SNP' 02), Braşov, p. 327-332.
PETRESCU, F. I. T.; PETRESCU, R. (2003) Some elements regarding the improvement of the engine design. Proceedings of the National Symposium, Descriptive Geometry, Technical Graphics and Design, (GTD' 03), Braşov, p. 353-358.
PETRESCU, F. I. T.; PETRESCU, R. (2005a) The cam design for a better efficiency. Proceedings of the International Conference on Engineering Graphics and Design, (EGD’ 05), Bucharest, p. 245-248.
PETRESCU, F. I. T.; PETRESCU, R. (2005b) Contributions at the dynamics of cams. Proceedings of the 9th IFToMM International Symposium on Theory of Machines and Mechanisms, (TMM’ 05), Bucharest, Romania, p. 123-128.
PETRESCU, F. I. T.; PETRESCU, R. (2005c) Determining the dynamic efficiency of cams. Proceedings of the 9th IFToMM International Symposium on Theory of Machines and Mechanisms, (TMM’ 05), Bucharest, Romania, p. 129-134.
PETRESCU, F. I. T.; PETRESCU, R. (2005d) An original internal combustion engine. Proceedings of the 9th IFToMM International Symposium on Theory of Machines and Mechanisms, (TMM’ 05), Bucharest, Romania, p. 135-140.
PETRESCU, F. I. T.; PETRESCU, R. (2005e) Determining the mechanical efficiency of Otto engine’s mechanism. Proceedings of the 9th IFToMM International Symposium on Theory of Machines and Mechanisms, (TMM 05), Bucharest, Romania, p. 141-146.
PETRESCU, F. I. T.; PETRESCU, R. V. V. (2011a) Dinamica mecanismelor de distributie, Create Space publisher, USA, ISBN 978-1-4680-5265-7, 188 pages, Romanian version.
PETRESCU, F. I. T.; PETRESCU, R. (2011b) Mechanical Systems, Serial and Parallel (Romanian). 1st Edn.; LULU Publisher, London, UK, p. 124.
PETRESCU, F. I. T.; PETRESCU, R. (2011c) Trenuri Planetare. Createspace Independent Pub.; 104 pages, ISBN-13: 978-1468030419.
PETRESCU, F. I. T.; PETRESCU, R. (2012a) Kinematics of the planar quadrilateral mechanism. ENGEVISTA, n. 14, p. 345-348.
PETRESCU, F. I. T.; PETRESCU, R. (2012b) Mecatronica-Sisteme Seriale si Paralele. 1st Edn.; Create Space Publisher, USA, p. 128.
PETRESCU, F. I. T.; PETRESCU, R. V. (2013a) An Algorithm for Setting the Dynamic Parameters of the Classic Distribution Mechanism, In IREMOS Journal, ISSN: 1974-9821, v. 6, n. 5, Part B, p. 1637-1641.
PETRESCU, F. I. T.; PETRESCU, R. V. (2013b) Dynamic Synthesis of the Rotary Cam and Translated Tappet with Roll, In IREMOS Journal, ISSN: 1974-9821, v. 6, n. 2, Part B, April 2013, p. 600-607.
PETRESCU, F. I. T.; PETRESCU, R. V. (2013c) Forces and Efficiency of Cams, in IREME, v. 7, n. 3, p. 507-511.
PETRESCU, F. I. T.; PETRESCU, R. V. (2013d) Cams with High Efficiency, in IREME, v. 7, n. 4, p. 599-606.
PETRESCU, F. I. T.; PETRESCU, R. (2013e) Cinematics of the 3R dyad. ENGEVISTA, n. 15, p. 118-124.
PETRESCU, F. I. T.; PETRESCU, R. V. (2014) Cam Gears Dynamics in the Classic Distribution. In Independent Journal of Management & Production, ISSN: 2236-269X, v. 5, n. 1, p. 166-185.
PETRESCU, F. I. T.; PETRESCU, R. (2016a) Parallel moving mechanical systems kinematics. ENGEVISTA, n. 18, p. 455-491.
PETRESCU, F. I. T.; PETRESCU, R. (2016b) Direct and inverse kinematics to the anthropomorphic robots. ENGEVISTA, n. 18, p. 109-124.
PETRESCU, F. I. T.; PETRESCU, R. (2016c) Dynamic cinematic to a structure 2R. Revista Geintec-Gestao Inovacao E Tecnol., n. 6, p. 3143-3154.
PETRESCU, R. V.; AVERSA, R.; APICELLA, A.; PETRESCU, F. I. T. (2016) Future medicine services robotics. Am. J. Eng. Applied Sci., n. 9, p. 1062-1087. DOI: 10.3844/ajeassp.2016.1062.1087
PETRESCU, F. I. T.; GRECU, B.; COMANESCU, A.; PETRESCU, R. V. V. (2009) Some mechanical design elements. Proceeding of the International Conference on Computational Mechanics and Virtual Engineering, (MVE’ 09), Braşov, p. 520-525.
PETRESCU, F. I. T. (2011) Teoria Mecanismelor si a Masinilor: Curs Si Aplicatii. 1st Edn.; CreateSpace Independent Publishing Platform. ISBN-10: 1468015826. P. 432.
PETRESCU, F. I. T. (2012a) Bazele analizei și optimizării sistemelor cu memorie rigidă – curs și aplicații, Create Space publisher, USA, 2012, ISBN 978-1-4700-2436-9, 164 pages, Romanian edition.
PETRESCU, F. I. T. (2012b) Teoria mecanismelor – Curs si aplicatii (editia a doua), Create Space publisher, USA, September 2012, ISBN 978-1-4792-9362-9, 284 pages, Romanian version.
PETRESCU, F. I. T. (2015a) Geometrical synthesis of the distribution mechanisms. Am. J. Eng. Applied Sci., n. 8, p. 63-81. DOI: 10.3844/ajeassp.2015.63.81
PETRESCU, F. I. T. (2015b) Machine motion equations at the internal combustion heat engines. Am. J. Eng. Applied Sci., n. 8, p. 127-137. DOI: 10.3844/ajeassp.2015.127.137
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; BUCINELL, R.; CORCHADO, J. (2017ª) Yield at thermal engines internal combustion. Am. J. Eng. Applied Sci., n. 10, p. 243-251. DOI: 10.3844/ajeassp.2017.243.251
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; RONALD, B.; CORCHADO, J. (2017b) Velocities and accelerations at the 3R mechatronic systems. Am. J. Eng. Applied Sci., n. 10, p. 252-263. DOI: 10.3844/ajeassp.2017.252.263
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; BUCINELL, R.; CORCHADO, J. (2017c) Anthropomorphic solid structures n-r kinematics. Am. J. Eng. Applied Sci., n. 10, p. 279-291. DOI: 10.3844/ajeassp.2017.279.291
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; BUCINELL, R.; CORCHADO, J. (2017d) Inverse kinematics at the anthropomorphic robots, by a trigonometric method. Am. J. Eng. Applied Sci., n. 10, p. 394-411. DOI: 10.3844/ajeassp.2017.394.411
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; BUCINELL, R.; CORCHADO, J. (2017e). Forces at internal combustion engines. Am. J. Eng. Applied Sci., n. 10, p. 382-393. DOI: 10.3844/ajeassp.2017.382.393
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; BUCINELL, R.; CORCHADO, J. (2017f) Gears-Part I. Am. J. Eng. Applied Sci., n. 10, p. 457-472. DOI: 10.3844/ajeassp.2017.457.472
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; BUCINELL, R.; CORCHADO, J. (2017g) Gears-part II. Am. J. Eng. Applied Sci., n. 10, p. 473-483. DOI: 10.3844/ajeassp.2017.473.483
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; BUCINELL, R.; CORCHADO, J. (2017h) Cam-gears forces, velocities, powers and efficiency. Am. J. Eng. Applied Sci., n. 10, p. 491-505. DOI: 10.3844/ajeassp.2017.491.505
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; BUCINELL, R.; CORCHADO, J. (2017i) Dynamics of mechanisms with cams illustrated in the classical distribution. Am. J. Eng. Applied Sci., n. 10, p. 551-567. DOI: 10.3844/ajeassp.2017.551.567
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; BUCINELL, R.; CORCHADO, J. (2017j) Testing by non-destructive control. Am. J. Eng. Applied Sci., n. 10, p. 568-583. DOI: 10.3844/ajeassp.2017.568.583
PETRESCU, R. V.; AVERSA, R.; APICELLA, A.; PETRESCU, F. I. T. (2017k) Transportation engineering. Am. J. Eng. Applied Sci., n. 10, p. 685-702. DOI: 10.3844/ajeassp.2017.685.702
PETRESCU, R. V.; AVERSA, R.; KOZAITIS, S.; APICELLA, A.; PETRESCU, F. I. T.; (2017l) The quality of transport and environmental protection, part I. Am. J. Eng. Applied Sci., n. 10, p. 738-755. DOI: 10.3844/ajeassp.2017.738.755
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; BUCINELL, R.; CORCHADO, J. (2017m0 Modern propulsions for aerospace-a review. J. Aircraft Spacecraft Technol., n. 1, p. 1-8. DOI: 10.3844/jastsp.2017.1.8
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; BUCINELL, R.; CORCHADO, J. (2017n) Modern propulsions for aerospace-part II. J. Aircraft Spacecraft Technol., n. 1, p. 9-17. DOI: 10.3844/jastsp.2017.9.17
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; BUCINELL, R.; CORCHADO, J. (2017º) History of aviation-a short review. J. Aircraft Spacecraft Technol., n. 1, p. 30-49. DOI: 10.3844/jastsp.2017.30.49
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; BUCINELL, R.; CORCHADO, J. (2017p) Lockheed martin-a short review. J. Aircraft Spacecraft Technol., n. 1, p. 50-68. DOI: 10.3844/jastsp.2017.50.68
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; CORCHADO, J.; BERTO, F. (2017q) Our universe. J. Aircraft Spacecraft Technol., n. 1, p. 69-79. DOI: 10.3844/jastsp.2017.69.79
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; CORCHADO, J.; BERTO, F. (2017r) What is a UFO? J. Aircraft Spacecraft Technol., n. 1, p. 80-90. DOI: 10.3844/jastsp.2017.80.90
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; CORCHADO, J.; BERTO, F. (2017s) About bell helicopter FCX-001 concept aircraft-a short review. J. Aircraft Spacecraft Technol., n. 1, p. 91-96. DOI: 10.3844/jastsp.2017.91.96
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; CORCHADO, J.; BERTO, F. (2017t) Home at airbus. J. Aircraft Spacecraft Technol., n. 1, p. 97-118. DOI: 10.3844/jastsp.2017.97.118
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; CORCHADO, J.; BERTO, F. (2017u) Airlander. J. Aircraft Spacecraft Technol., n. 1, p. 119-148. DOI: 10.3844/jastsp.2017.119.148
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; CORCHADO, J.; BERTO, F. (2017v) When boeing is dreaming-a review. J. Aircraft Spacecraft Technol., n. 1, p. 149-161. DOI: 10.3844/jastsp.2017.149.161
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; CORCHADO, J.; BERTO, F. (2017w) About Northrop Grumman. J. Aircraft Spacecraft Technol., n. 1, p. 162-185. DOI: 10.3844/jastsp.2017.162.185
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; CORCHADO, J.; BERTO, F. (2017x) Some special aircraft. J. Aircraft Spacecraft Technol., n. 1, p. 186-203. DOI: 10.3844/jastsp.2017.186.203
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; CORCHADO, J.; BERTO, F. (2017y) About helicopters. J. Aircraft Spacecraft Technol., n. 1, p. 204-223. DOI: 10.3844/jastsp.2017.204.223
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; BERTO, F.; APICELLA, A. (2017z) The modern flight. J. Aircraft Spacecraft Technol., n. 1, p. 224-233. DOI: 10.3844/jastsp.2017.224.233
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; BERTO, F.; APICELLA, A. (2017aa) Sustainable energy for aerospace vessels. J. Aircraft Spacecraft Technol. , n. 1, p. 234-240. DOI: 10.3844/jastsp.2017.234.240
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; BERTO, F.; APICELLA, A. (2017ab) Unmanned helicopters. J. Aircraft Spacecraft Technol., n. 1, p. 241-248. DOI: 10.3844/jastsp.2017.241.248
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; BERTO, F.; APICELLA, A. (2017ac) Project HARP. J. Aircraft Spacecraft Technol., n. 1, p. 249-257. DOI: 10.3844/jastsp.2017.249.257
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; BERTO, F.; APICELLA, A. (2017ad) Presentation of Romanian engineers who contributed to the development of global aeronautics-part I. J. Aircraft Spacecraft Technol., n. 1, p. 258-271. DOI: 10.3844/jastsp.2017.258.271
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; BERTO, F.; APICELLA, A. (2017ae) A first-class ticket to the planet mars, please. J. Aircraft Spacecraft Technol., n. 1, p. 272-281. DOI: 10.3844/jastsp.2017.272.281
PETRESCU, R. V.; AVERSA, R.; APICELLA, A.; MIRSAYAR, M. M.; KOZAITIS, S. (2018a) NASA started a propeller set on board voyager 1 after 37 years of break. Am. J. Eng. Applied Sci. , n. 11, p. 66-77. DOI: 10.3844/ajeassp.2018.66.77
PETRESCU, R. V.; AVERSA, R.; APICELLA, A.; MIRSAYAR, M. M.; KOZAITIS, S. (2018b) There is life on mars? Am. J. Eng. Applied Sci. , n. 11, p. 78-91. DOI: 10.3844/ajeassp.2018.78.91
PETRESCU, R. V.; AVERSA, R.; APICELLA, A.; PETRESCU, F. I. T. (2018c) Friendly environmental transport. Am. J. Eng. Applied Sci. , n. 11, p. 154-165. DOI: 10.3844/ajeassp.2018.154.165
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; ABU-LEBDEH, T. M.; APICELLA, A. (2018d) Buses running on gas. Am. J. Eng. Applied Sci. , n. 11, p. 186-201. DOI: 10.3844/ajeassp.2018.186.201
PETRESCU, R. V.; AVERSA, R.; AKASH, B.; ABU-LEBDEH, T. M.; APICELLA, A. (2018e) Some aspects of the structure of planar mechanisms. Am. J. Eng. Applied Sci., n. 11, p. 245-259. DOI: 10.3844/ajeassp.2018.245.259
PETRESCU, R. V.; AVERSA, R.; ABU-LEBDEH, T. M.; APICELLA, A.; PETRESCU, F. I. T. (2018f) The forces of a simple carrier manipulator. Am. J. Eng. Applied Sci., n. 11, p. 260-272. DOI: 10.3844/ajeassp.2018.260.272
PETRESCU, R. V.; AVERSA, R.; ABU-LEBDEH, T. M.; APICELLA, A.; PETRESCU, F. I. T. (2018g) The dynamics of the otto engine. Am. J. Eng. Applied Sci., n. 11, p. 273-287. DOI: 10.3844/ajeassp.2018.273.287
PETRESCU, R. V.; AVERSA, R.; ABU-LEBDEH, T. M.; APICELLA, A.; PETRESCU, F. I. T. (2018h) NASA satellites help us to quickly detect forest fires. Am. J. Eng. Applied Sci., n. 11, p. 288-296. DOI: 10.3844/ajeassp.2018.288.296
PETRESCU, R. V.; AVERSA, R.; ABU-LEBDEH, T. M.; APICELLA, A.; PETRESCU, F. I. T. (2018i) Kinematics of a mechanism with a triad. Am. J. Eng. Applied Sci., n. 11, p. 297-308. DOI: 10.3844/ajeassp.2018.297.308
PETRESCU, R. V.; AVERSA, R.; APICELLA, A.; PETRESCU, F. I. T. (2018j) Romanian engineering "on the wings of the wind". J. Aircraft Spacecraft Technol. , n. 2, p. 1-18. DOI: 10.3844/jastsp.2018.1.18
PETRESCU, R. V.; AVERSA, R.; APICELLA, A.; PETRESCU, F. I. T. (2018k) NASA Data used to discover eighth planet circling distant star. J. Aircraft Spacecraft Technol., n. 2, p. 19-30. DOI: 10.3844/jastsp.2018.19.30
PETRESCU, R. V.; AVERSA, R.; APICELLA, A.; PETRESCU, F. I. T. (2018l) NASA has found the most distant black hole. J. Aircraft Spacecraft Technol. , n. 2, p. 31-39. DOI: 10.3844/jastsp.2018.31.39
PETRESCU, R. V.; AVERSA, R.; APICELLA, A.; PETRESCU, F. I. T. (2018m) Nasa selects concepts for a new mission to titan, the moon of saturn. J. Aircraft Spacecraft Technol. , n. 2, p. 40-52. DOI: 10.3844/jastsp.2018.40.52
PETRESCU, R. V.; AVERSA, R.; APICELLA, A.; PETRESCU, F. I. T. (2018n) NASA sees first in 2018 the direct proof of ozone hole recovery. J. Aircraft Spacecraft Technol., n. 2, p. 53-64. DOI: 10.3844/jastsp.2018.53.64
POURMAHMOUD, N. (2008) Rarefied Gas Flow Modeling inside Rotating Circular Cylinder, Am. J. Eng. Applied Sci., v. 1, n. 1, p. 62-65. DOI: 10.3844/ajeassp.2008.62.65
RAHMANI, L.; DRAOUI, B.; BOUANINI, M.; BENACHOUR, E. (2013) CFD Study on Heat Transfer to Bingham Fluid During with Gate Impeller, in IREME, v. 7, n. 6, p. 1074-1079.
RAJASEKARAN, A.; RAGHUNATH, P. N.; SUGUNA, K. (2008) Effect of Confinement on the Axial Performance of Fibre Reinforced Polymer Wrapped RC Column, Am. J. Eng. Applied Sci., v. 1, n. 2, p. 110-117. DOI: 10.3844/ajeassp.2008.110.117
RAVI, S.; SUBRAMANIAN, R. (2013) Diesel Fuel Additives: an Overview, in IREME, v. 7, n. 4, p. 698-704.
RONNEY, P. D.; SHODA, M.; WAIDA, S. T.; DURBIN, E. J. (1994) Throttleless Premixed-Charge Engines: Concept and Experiment, in Journal of Automobile Engineering, v. 208, p. 13-24.
SAPATE, K. D.; TIKEKAR, A. N. (2013) Engine Mapping for Improvement in Fuel Efficiency of Two Stroke SI Engine, in IREME, v. 7, n. 3, p. 392-394.
SETHUSUNDARAM, P. P.; ARULSHRI, K. P.; MYLSAMY, K. (2013) Biodiesel Blend, Fuel Properties and its Emission Characteristics Sterculia Oil in Diesel Engine, in IREME, v. 7, n. 5, p. 925-929.
SHOJAEEFARD, M. H.; GOUDARZI, K.; NOORPOOR, A. R.; FAZELPOUR, M. (2008) A Study of Thermal Contact using Nonlinear System Identification Models, Am. J. Eng. Applied Sci., v. 1, n. 1, p. 16-23. DOI: 10.3844/ajeassp.2008.16.23
TAHER, S. A.; HEMATTI, R.; NEMATI, M. (2008) Comparison of Different Control Strategies in GA-Based Optimized UPFC Controller in Electric Power Systems, Am. J. Eng. Applied Sci., v. 1, n. 1, p. 45-52. DOI: 10.3844/ajeassp.2008.45.52
TAVALLAEI, M. A.; TOUSI, B. (2008) Closed Form Solution to an Optimal Control Problem by Orthogonal Polynomial Expansion, Am. J. Eng. Applied Sci., v. 1, n. 2, p. 104-109. DOI: 10.3844/ajeassp.2008.104.109
THEANSUWAN, W.; TRIRATANASIRICHAI, K. (2008) Air Blast Freezing of Lime Juice: Effect of Processing Parameters, Am. J. Eng. Applied Sci., v. 1, n. 1, p. 33-39. DOI: 10.3844/ajeassp.2008.33.39
ZAHARI, I.; ABRAS, M. A.; MAT ARISHAD, N. I.; ZAINAL, S. F.; MUHAMAD, M. F. (2013) Experimental Study to Identify Common Engine Part Load Conditions between Malaysian City Driving and NEDC Test, in IREME, v. 7, n. 6, p. 1152-1158.
ZAHEDI, S. A.; VAEZI, M.; TOLOU, N. (2008) Nonlinear Whitham-Broer-Kaup Wave Equation in an Analytical Solution, Am. J. Eng. Applied Sci., v. 1, n. 2, p. 161-167. DOI: 10.3844/ajeassp.2008.161.167
ZHU, G. et al. (2007) Closed-Loop Ignition Timing Control for SI Engines Using Ionization Current Feedback, IEEE Trans on Control Systems, p. 416-427.
ZULKIFLI, R.; SOPIAN, K.; ABDULLAH, S.; TAKRIFF, M. S. (2008) Effect of Pulsating Circular Hot Air Jet Frequencies on Local and Average Nusselt Number, Am. J. Eng. Applied Sci., v. 1, n. 1, p. 57-61. DOI: 10.3844/ajeassp.2008.57.61